Describe your job, get a tailored proposal
Tell us the material, thickness and industry. The page below is regenerated around your requirement — with the machines and the process advice that match it.
Tube Laser Process Advice (Ø50–300)
- 01Step 01
Confirm Material and Thickness
Check that your tube material and wall thickness fall within the capability of the LP-T320-4kW and the LP-F6000 Heavy-Duty Fiber Series before programming the job.
- 02Step 02
Set Cutting Parameters and Gas
Select cutting parameters and assist gas according to the LaserPeak laser technology guidance for your material and thickness, without inventing values beyond the site content.
- 03Step 03
Plan Fixturing and Support
Fixture and support the Ø50–300 tube so it stays stable and aligned during cutting, using the machine's tube-handling setup for this diameter range.
- 04Step 04
Validate Before Production
Run a trial cut and inspect the result against your requirements before starting full production, confirming the setup matches the published LaserPeak specifications.
Preliminary process advice based on the requirement you described. Final parameters are confirmed by a trial cut on your material before production.
Tube laser for Ø50–300 mm tubes
The LP-T320-4kW is our tube laser for this diameter range. See the LP-F6000 Heavy-Duty Fiber Series catalogue for related fiber laser technology.
A 3 kW fibre laser in a 3000×1500 mm format, the LP-F1503-3kW cuts 3 mm carbon steel at about 12 m/min and reaches 10 mm mild steel at rated power. Pneumatic pallet exchange, automatic nozzle control and a compact footprint make it a strong production cell for small and mid-size job shops.
- Power
- 3 kW
- Cutting area
- 3000×1500 mm
- Accuracy
- ±0.02 mm
The 1.5 kW version of the LP-F1500 platform for thin sheet, precision blanks and high-volume small parts. It cuts thin stainless at more than 30 m/min, minimizes heat-affected zones on delicate workpieces and draws considerably less power than comparable carbon dioxide installations.
- Power
- 1.5 kW
- Cutting area
- 3000×1500 mm
- Accuracy
- ±0.02 mm
The 40 kW flagship with an 8000×2500 mm bed, cutting 30 mm carbon steel in one pass and handling the largest structural blanks in the LaserPeak range. It targets shipbuilding, defence platforms and heavy equipment where very thick plate is cut as single pieces.
- Power
- 40 kW
- Cutting area
- 8000×2500 mm
- Accuracy
- ±0.02 mm
A 30 kW laser on the 6000×2500 mm platform for the thickest production plate. It cuts 25 mm carbon steel at about 2.5 m/min and 30 mm at roughly 1.5 m/min, letting fabricators consolidate large-plate work that previously went to waterjet or multiple oxy-fuel stations.
- Power
- 30 kW
- Cutting area
- 6000×2500 mm
- Accuracy
- ±0.02 mm
The LP-A2000 automates sheet handling around LaserPeak fibre cutting machines, with interchangeable lifting tables, automatic pallet exchange, sheet following and robot loading arms. Unattended hours increase while operators move from handling heavy plate to programming and inspection.
- Cutting area
- Serves 1500×750 to 6000×2500 mm sheet platforms
- Accuracy
- ±0.05 mm sheet positioning
A 10 kW laser on the 4000×2000 mm bed for large-format panels in one piece. It cuts 6 mm carbon steel at about 9 m/min and handles 20 mm plate, giving structural, vehicle-body and enclosure manufacturers a single machine for full-width blanks with no part splitting.
- Power
- 10 kW
- Cutting area
- 4000×2000 mm
- Accuracy
- ±0.02 mm
Send the requirement to an application engineer
Your inquiry carries the requirement text, so the engineer replying already knows the material and the thickness.