Describe your job, get a tailored proposal
Tell us the material, thickness and industry. The page below is regenerated around your requirement — with the machines and the process advice that match it.
Process Advice for 40kW Heavy Plate Cutting
- 01Step 01
Confirm Material and Thickness
Check that your plate material and thickness fall within the heavy-duty plate cutting scope covered by the LP-F6000 Heavy-Duty Fiber Series and the LP-F12000 12 kW fiber laser for heavy-duty plate cutting.
- 02Step 02
Select Cutting Parameters and Gas
Set cutting parameters and assist gas based on the parameters documented in the LP-F6000 Heavy-Duty Fiber Series catalogue for your material and thickness; do not use values outside the published site content.
- 03Step 03
Plan Fixturing and Support
Prepare fixturing and support suited to heavy-duty plate so the workpiece stays stable during cutting, consistent with the heavy-plate focus of the LP-F6000 Heavy-Duty Fiber Series.
- 04Step 04
Validate Before Production
Run a validation cut and compare results against the LP-F6000 Heavy-Duty Fiber Series catalogue guidance before committing to full production.
Preliminary process advice based on the requirement you described. Final parameters are confirmed by a trial cut on your material before production.
Heavy-duty fiber laser for thick plate cutting
The LP-F6000 Heavy-Duty Fiber Series is built for heavy-duty plate cutting, and the LP-F12000 12 kW fiber laser extends the range for demanding thick-plate work.
A 3 kW fibre laser in a 3000×1500 mm format, the LP-F1503-3kW cuts 3 mm carbon steel at about 12 m/min and reaches 10 mm mild steel at rated power. Pneumatic pallet exchange, automatic nozzle control and a compact footprint make it a strong production cell for small and mid-size job shops.
- Power
- 3 kW
- Cutting area
- 3000×1500 mm
- Accuracy
- ±0.02 mm
A 3 kW laser welding cell with a 2000×1000 mm fixture for sheet and tube assemblies. It keyhole-welds 1.5–3 mm lap joints, handles 0.8–4 mm stainless and galvanized sheet up to 2 mm, and replaces TIG stations with a faster, more repeatable process.
- Power
- 3 kW
- Cutting area
- 2000×1000 mm welding fixture, expandable to 3000×1500 mm
- Accuracy
- ±0.1 mm
The 1.5 kW version of the LP-F1500 platform for thin sheet, precision blanks and high-volume small parts. It cuts thin stainless at more than 30 m/min, minimizes heat-affected zones on delicate workpieces and draws considerably less power than comparable carbon dioxide installations.
- Power
- 1.5 kW
- Cutting area
- 3000×1500 mm
- Accuracy
- ±0.02 mm
The 40 kW flagship with an 8000×2500 mm bed, cutting 30 mm carbon steel in one pass and handling the largest structural blanks in the LaserPeak range. It targets shipbuilding, defence platforms and heavy equipment where very thick plate is cut as single pieces.
- Power
- 40 kW
- Cutting area
- 8000×2500 mm
- Accuracy
- ±0.02 mm
A 30 kW laser on the 6000×2500 mm platform for the thickest production plate. It cuts 25 mm carbon steel at about 2.5 m/min and 30 mm at roughly 1.5 m/min, letting fabricators consolidate large-plate work that previously went to waterjet or multiple oxy-fuel stations.
- Power
- 30 kW
- Cutting area
- 6000×2500 mm
- Accuracy
- ±0.02 mm
The LP-A2000 automates sheet handling around LaserPeak fibre cutting machines, with interchangeable lifting tables, automatic pallet exchange, sheet following and robot loading arms. Unattended hours increase while operators move from handling heavy plate to programming and inspection.
- Cutting area
- Serves 1500×750 to 6000×2500 mm sheet platforms
- Accuracy
- ±0.05 mm sheet positioning
Send the requirement to an application engineer
Your inquiry carries the requirement text, so the engineer replying already knows the material and the thickness.